NEW V4 - Additive Layering
Additive Overlays , what they are
In ACF, Overlays are animation layers that get blended on top of your base locomotion (moveset), usually affecting the upper body (aiming, blocking, holding weapons, etc.) without swapping the whole locomotion layer. ACF keeps the “main ABP” mostly logic-only, and pushes animations into Linked Animation Layers that can be swapped at runtime.
In ACF v4 specifically, OverlayLayers use GameplayTags to swap between overlay animations/layers, so the system knows which overlay to activate depending on weapon/state.
After creating your overlay layer AnimBP, you must assign it inside the main AnimBlueprint (your ACF template AnimInstance) in the GameplayTag → Overlay Layer map, otherwise it cannot be activated/swapped.
Create your Custom Additive Overlay
To get started I will the primary Linked Animation Layer that drives the logic of this system is located at /All/Game/GASP/Animations/Overlays/Additive

The Rifle Linked Anim Layer is a Child of this Animation Blueprint and is located at /All/Game/GASP/Animations/Overlays/Additive/Weapons

If you need to create a new linked animation layer for a new set of Poses you have made you can create one by Right Clicking on the ‘ACF_MMBaseAdditiveOverlay’ Animation Instance located at /All/Game/GASP/Animations/Overlays/Additive and selecting ‘Create Child Anim Blueprint with Skeleton’ After this, select the ’UEFN Skeleton’ from the List that is used by that Animation Instance and select ’Create Child’

After you have created it, you can open it up and select ‘Class Defaults’. You will notice that all the settings are exposed in the Details, this is where Poses and Data Assets for the Layering Settings will be assigned.

We will first start with the Settings Category under ACF->Settings. These require Data Assets which will allow you to adjust the amount of Motion that gets layered onto the pose and by how much.
Layering Settings
The Data Asset is called PDA_LayeringSettings and is located at /All/Game/GASP/Animations/Overlays/Additive/Data/Essentials To create a new Data Asset you will need to right click in your folder and go to Miscellaneous->DataAsset. In the window that comes up search for PDA_LayeringSettings and select it.
Create one for each of the modes that are relevant to you, if you only need Aim and Idle then create one for each. Each Setting influences the layering result. You have two options for each an Overlay Type and an Overlay Weight.

The Overlay Types: Determine how that motion is layered, the common ones you will use are already set as the default for each limb, but I suggest you look at the Templates to see how I set those up as well. I encourage people to experiment with these settings during Run-Time as the changes you make will immediately be reflected within the game while it is running
The Overlay Weight: Is essentially the percentage of this pose with this OverlayType, we will be applying to the Locomotion.
Base Pose: This represents the actual Locomotion Animation and allows you to have specific limbs for example the Left Arm, not be layered or only layered by a specified amount.
Overlay Pose: This is the Actual Pose we are Layering and is Stiff. In some cases, we may want to stiffen part of the body to favor that pose but only by a specified amount. This allows us to Reduce the amount of influence that the Locomotion animation has on this part of the body.
Mesh Space: This will transfer the Motion onto the Pose and ensure that the motion moves relative to the direction it moves in the animation. If a leg is moving back and forth, regardless of the orientation of the Leg in the Pose, it will still move back and forth.
Local Space: This will transfer the Motion onto the Pose relative to the Pose. This means that if the leg is rotated to the right, and the leg in the animation is moving back and forth, it will now move left to right. For the Lower Body you almost never want to layer it in Local Space, but in situations where you want the orientation of bones to influence the direction of motion you would want this, such as on the arms perhaps.
Arm: Arm L and Arm R is layered with a Mesh Space Rotation Blend; this means it will be oriented as it were in the actual Pose relative to the Space you see from the Preview window when you open the Animation.
Arm Secondary: The Secondary allows you to apply a percent of motion on top of that. Normally on the Arms, when we are aiming, we want it to be accurate, and so we set our Layering type to Overlay for a stiff Pose with a weight of 1.0 and then we can add a little bit of Secondary Motion on top to re-introduce motion back into the pose so that it doesn’t appear stiff anymore.
Upper Body Secondary: This allows us to re-introduce Secondary Motion onto the Upper Body in situations were doing so on the Arms themselves may Desynchronize the Arms from the Torso and cause it to move unnaturally, causing issues between the upper arm and clavicle. If we need the Aim to be more accurate and move around less but without looking stiff, then we may stiffen the Torso and the Arms, and then just add Secondary